If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
First, we need to drill out the holes for the screws that will hold them together. While the two layers of MDF are glued, the countertop and the MDF will only be screwed. The oak countertop, like any natural wood product, will expand and contract with humidity changes. If it were glued to the MDF, the difference in expansion of the two layers would cause the countertop to buckle and curl.
2. Bill Hylton's Power-Tool Joinery by Bill Hylton. From the editors of Popular Woodworking magazine, this is a go-to for setting up power tools for making joinery. Organized by joint type - rabbets, half-laps, dovetails, etc - it provides detailed instructions show you how to make each joint with every tool possible. I especially like the jigs and fixtures details that show you there's definitely more than one way to skin that cat.

I know, if you had a workbench, you wouldn't be building a workbench. Even so, you'll need some sort of work surface, even if it isn't as stable or capable as a proper bench. The traditional solution is to throw a hollow-core door over a couple of saw horses. The advantage of hollow core doors is that they're flat, stiff, and cheap. I used a folding table and a hollow core door I had bought for a future project.

Assemble the vises, for the final time. You'll not be taking them off again, so tighten everything down, and attach the endplate to the ends of the screw and guide rods. Then mark and drill benchdog holes in the outer jaws inline with the benchdog holes in the top. Generally, through-holes are preferred for benchdogs, so that they don't collect sawdust and gunk. With these vises, that isn't possible, there are screws and guide rods in the way. I drilled them just deep enough to hold a Veritas Bench Pony (their reduced-height benchdog), without it sinking to where I can't get a grip to remove it. Rockler sells some very inexpensive plastic benchdogs that can't be adjusted for height, and aren't as strong as metal or wooden dogs, that I intend to keep in the holes full-time, to keep sawdust from collecting in them.
I decided to make my own top out of white ash because I had access to a planer and jointer at my local college where I was taking an intro woodworking class. Trim and vice jaws are white ash as well. Everything else is built pretty much as jdege describes. A plunge router with a 3/4" spiral up bit really made quick work of the dog holes. Finished with Danish oil.

The Handplane Book is a complete guide to one of the best known and most collectable hand tools. It covers all the basics, including how to buy a plane, tune it up, and use it. Fascinating background information on the development and manufacture of handplanes shows the rich heritage of this versatile tool. Focusing on planes from the golden age of the handplanes (19th and early 20th century), it also profiles tools from many sources around the world.
For one, the bench itself is a good size. While its width as a tad short at just over 1 ½’, the length is a great 5’ long. Even better, this bench is made out of birch wood. Birchwood is similar to beech in that it is strong but soft enough to prevent inadvertent dulling of your tools. However, birch has a bit of an advantage over beech in that it is not a porous which makes staining on the Windsor Design a more worry-free affair.
Another comprehensive book by Taunton Press, Wood Flooring is extremely informative, not to mention visually compelling. From subfloors to finishing, and everything in between, you can be sure this is the only book you will ever need on the subject. My favou­rite chapter was on inlays and curves: using jigs and templates to add circular inlays to a floor, laying out and installing laminated curves, even working with stone and metal inlays … there’s a lot to learn in that one chapter alone. Much of it could be adapted to making furniture. If you want to lay a basic wood floor this book will help you add lasting value and beauty to your home. If you’re looking to one-up your super handy DIY brother-in-law, you can start here too.
I was using 2-1/2" coarse Kreg pocket hole screws. Kreg screws are supposed to be self-tapping, but the coarse-thread screws are intended to be self-tapping in softwood, and the fine-thread screws they intend for use in hardwoods aren't available in 2-1/2" lengths. I decided to drill pilot holes in the oak. Just to make sure, I did a test hole in the scrap piece I'd cut off.
Woodturning: A Foundation Course When I decided to go beyond just turning writing pens, I turned to this book to help broaden my knowledge of woodturning. You will learn the tools of the trade and sharpening techniques for your turning tools. It introduces several turning projects like bowls, pepper mills, and table lamps. You also learn how to sand and finish your turned creations.
If you're using drywall screws, you'll want to countersink the holes. Drywall screws are flat-head, and need a countersink to seat solidly. If you're using Kreg pocket screws, the way I did, you won't want to counter-sink the holes. Kreg screws are pan-head, and seat just fine against a flat surface. Both drywall screws and Kreg pocket screws are self-threading, so you don't need pilot holes in the second sheet of MDF.
I don't see anywhere you mentioned the over all length of the bench top. A piece of 1 1/2" x 25" x 8' glued edge oak at Lumber Liquidators costs $192 including tax. Two piece is almost $400! Would that be better if I use two IKEA 1 1/4" x 25" x 74" solid Beech ($99 each plus tax) on top of a layer of 3/4" Birch plywood. That would be 3 1/4" over all.
 Watching all of these crafters for the past few weeks has not only been the highlight of my week, but it has inspired me to learn more about crafting and explore my own creativity through their different mediums. Inevitably, I fell down an internet rabbit hole of research and excitement (including Kristen McQuinn’s piece on Books About Traditional Crafts) and found myself enthralled by what I found on the craft of my childhood, woodworking.

Windsor Design is an interesting brand in that it is not actually its own company. Instead, Windsor Design is one of the in-house brands sold by Harbor Freight. While it may be a store brand, that should not dissuade you at all as Harbor Freight is known for selling some of the best products available for all fields of construction. Granted, this may not strictly be the best table available, but it does provide a solid mix of features to make it a good value.
×